FreePBX is a web-based open source GUI (graphical user interface) that controls and manages Asterisk (PBX), an open source communication server. FreePBX is licensed under the GNU General Public License (GPL), an open source license. FreePBX can be installed manually or as part of the pre-configured FreePBX Distro that includes the system OS, Asterisk, FreePBX GUI and assorted dependencies.
You'll need to have created an IP connection on your Telnyx Mission Control Portal account, assigned this connection to a DID and outbound profile in order to make and receive calls.
FreePBX V13 is available to download from here.
You can view the installation guide here.
Coming soon! This walkthrough will demonstrate setting up an IP based connection with FreePBX. We'll also show you how to assign this connection to a newly purchased DID which will allow you to receive inbound calls. Then we'll walk you through how to assign the connection to an outbound profile such that you can make outbound calls!
CONFIGURING YOUR TELNYX MISSION CONTROL PORTAL
Step by Step Guide
For step by step instructions on each of the requirements on the Telnyx Mission Control Portal, please follow this guide.
Once you've configured your Telnyx account, you can now proceed to setup FreePBX V13 following the guide below.
CONFIGURING YOUR FREEPBX V14
Step by Step Guide
You are now all set on the Mission Control Portal side and are ready to configure your Telnyx trunk within your FreePBX V14 system.
1. Once you load the ISO onto your server or virtual machine, you'll have a few options to select for installation. We'll be doing a full install via asterisk 13.
2. You'll be prompted for your preferred video method you want to install.
3. The installer will now start.
4. The installer will start but you will see it shows the root password is not set. You will need to click on the root password box to set your root password. The installation process can not complete until this is done.
5. Type in your root password and confirm it a second time and click on the Done option in the top left screen.
6. At this time the FreePBX package itself can take 15 or more minutes to install and does requires access to the internet so depending on your internet speeds it can take awhile to install so be patient.
7. Once the install has 100% completed it will give you a reboot option as shown below. Click on reboot your your system is now installed.
8. Once the process is complete, you'll reach the Linux console/command prompt login. You can log in here using the username "root" without quotes, and the Root password you selected earlier.
9. After you log in, you should see the IP address of your PBX as shown below. Take note of this IP address as you will need it in the next step.
10. Enter the IP address of the new PBX into your web browser. The first time you do so, you'll be asked to create the admin username and the admin password. That username and password will be used in the future to access the FreePBX configuration screen.
Note: These passwords do not change the Root password! They are only used for access to the FreePBX web interface.
11. The main FreePBX screen will offer you four options:
- FreePBX Administration will allow you to configure your PBX. Use the admin username and admin password you configured in the step above to login. This section is what most people refer to as "FreePBX."
- User Control Panel is where a user can log in to make web calls, set up their phone buttons, view voicemails, send and receive faxes, use SMS & XMPP messaging, view conferences, and more, depending on what you have enabled for the user.
- Operator Panel is a screen that allows an operator to control calls
- Get Support takes you to a web page about various official support options for FreePBX.
Basic Settings Configuration:
1. You'll be brought to the initial setup and must enter in the username, password and admin email address in order to create your account.
2. Once you've created your account, you'll be brought to the dashboard. Select FreePBX Administration and enter your username and password.
3. Follow the process to activate your FreePBX V13.
4. Select your default locales.
5. You'll be presented with some firewall details and other suggestions. You are welcome to set this up based on your requirements.
Eventually, you'll be back at the dashboard and now see more details.
At this point you can now work on confirming network settings and configuring your SIP trunks and extensions.
Make your way to Settings -> Asterisk SIP Settings in order to confirm your network settings.
You'll want to ensure you populate the external and local network addresses under General SIP Settings and Chan SIP Settings.
Click Submit and then Apply Config.
Make your way to Applications -> Extensions -> Add Extension -> Add New Chan SIP Extension. The Outbound CID is the number you purchased from your Telnyx Mission Control Portal. The extensions secret may need to be populated under the Other tab.
NOTE: This device uses CHAN_SIP technology listening on Port 5160 (UDP - this is a NON STANDARD port)
Click Submit and Apply Config.
For testing purposes, you can now use your SIP client to register with FreePBX using the username, password/secret and local IP address of your FreePBX.
Make your way to Connectivity -> Trunks -> Add Trunk -> Add New Chan SIP Trunk. You'll now be located in the General tab.
Enter a Trunk name, your Outbound CID and the maximum channels you'd like for this trunk.
Proceed to the Dialed Number Manipulation Rules tab.
Depending on your use case, we've provided a simple dial pattern US numbers below.
For US numbers:
- prepend:1; match pattern: NXXNXXXXXX
- prepend: blank; match pattern: 1NXXNXXXXXX
- prepend: Country Dialing prefix; match pattern: NXXNXXXXXX
- prepend:blank; match pattern: (Country Dialing prefix)NXXNXXXXXX
Proceed to the SIP Settings tab. In the sub tabs outgoing and incoming, you'll want to include the following below settings:
Outgoing SIP Settings for the trunk:
Inbound SIP Settings for the trunk:
Make your way to Connectivity -> Outbound Routes -> Add Outbound Route.
Enter the route name, route CID and specify the Telnyx_IP trunk for this outbound route. Click Submit and Apply Config.
Make your way to Connectivity -> Inbound Routes -> Add Inbound Route.
Enter the route name description, DID associated with this route and specify the extension that should be associated when calls are received to the DID.
Click Submit and Apply Config.
That's it, you've now completed the configuration of FreePBX V14 Credentials Trunk and can now make and receive calls by using Telnyx as your SIP provider!
Review our getting started with guide to make sure your Telnyx Mission Control Portal account is setup correctly!
Check out FreePBX's help section for community or paid support.
Can't find what you're looking for?
Our knowledge base is currently undergoing a makeover which will include more up to date videos to match our ever growing platform!
Can't find what you're looking for? Click the chat bubble at your lower right hand corner and start a chat!